ABB控制器中国地区唯一授权经销商
ABB 控制器 NextMove e100的详细描述：
轴数：在单个或多个坐标组中的16个插补轴，管理数十个独立的DS402定位驱动器（非插补）。
轴的类型：以太网Powerlink协议（EPL）v2，3个闭环轴±10V带有5VTTL渐进编码器输入接口，4个开环轴-步进电机接口（分布且定向输出）5V差分直线驱动器（5MHz）或由命令选项选出的5V开集电极单端（最大为500KHz）
Powerlink装置，以太网
单板存储器 固件为4M字节闪存和永久程序存储器为10M字节SRAM，永久变量数据存储器为32k字节FRAM
数字输入 20个光电分离的24VDC，采样率为1ms。所有的输入具有中断能力。可与正负公用块连接，可用于范围、位置、停机和驱动误差配置的软件
数字输出 12个光电分离的12-24VDC PNP 用于启动驱动器的可配置软件 每信道标准为50mA 单信道最大负载为350mA 8个信道合计500mA
模拟输出 对于驱动命令信号，有三种输出功率 ±10V、12位分辨率 一通用±10V12位输出
模拟输入 两种误差不超过V±10V，12位分辨率下运行
继电器输出 单输出适用于驱动器启用，额定值为24V（150mA）的C型继电器（单刀双郑），一般为常开常闭状态
串行口 RS485/232
Can总线端口 标准的9针Sub-D型连接器的单CAN端口等
NextMove e100Ethernet POWERLINK machine controller
The NextMove e100 builds on the proven NextMove controller family of products, integrating the management of real-time Ethernet using the industry standard protocol Ethernet POWERLINK. Drives, I/O devices, sensors, absolute encoders can all be added to the POWERLINK network and controlled from the MINT programming language. This greatly simplifies system design and installation, and simultaneously expands the capabilities of the NextMove e100 as a machine control platform.
NextMove e100 can perform interpolation for up to 16 axes, either as a single coordinate group or as an independent sub-group in a multitiple coordinate system with interpolation over the Ethernet POWERLINK network or the built in stepper/servo axes. NextMove e100 is compatible with ABB‘s Ethernet POWERLINK AC servo drives - MicroFlex e100 and MotiFlex e100.
NextMove e100 is part of the e100 motion family including MotiFlex e100, Mint Machine Modules and range of single phase servo drives, MicroFlex e100 all controlled via Ethernet POWERLINK.
NextMove e100 provides control of up to 16 coordinated axes of motion and many more non-coordinated axes. Axes can be split amongst the three phase MotiFlex e100 drives and single phase MicroFlex e100 drives to suit the application requirements.
Features:
Ethernet POWERLINK for real-time control of up to 16 axes of interpolated motion
Control of additional Ethernet POWERLINK devices, including drives, I/O and encoders
Compatible with MicroFlex e100 - providing a complete motion control solution
Integrated Ethernet hub for ease of wiring - simple daisy chain units together
Panel mount configuration with two part connectors
32-bit 120MHz Digital Signal Processor
1MByte SRAM for user programs and data
1MByte FLASH for firmware and user program storage
32kByte FRAM for non-volatile parameter storage
Onboard control for 3 axes of servo (+/-10V interface) & 4 axes of stepper (pulse and direction)
20 uncommitted PNP/NPN opto-isolated digital inputs
Programmable for hardware limits, home input, stop input and error input. 4 of the inputs can be programmed for high speed capture of position within 1 microsecond
12 uncommitted PNP opto-isolated digital outputs
Programmable for drive enable and high speed position compare output
4V/150mA relay output to signal system error conditions
2 x 12-bit uncommitted analog inputs
Uncommitted 12-bit analog output
RS232 & RS485 (User selectable. 115,200 Baud) and USB programming interfaces
USB drivers compatible with Windows 2000/XP
CAN interface for I/O expansion and HMI interfaces. Can be used to provide full peer-to-peer networking capabilities with other Mint based controllers
Multitasking programming capability with Mint. Number of tasks limited only by available memory
Comprehensive move types including: linear, circular and helical interpolation; software cams; flying shears; splines; synchronization with positional offsets and virtual axes
ActiveX libraries supplied free of charge
Compatible with MintNC and HPGL
Ordering information and accessories:
Catalog numberDescription
NXE100-1608DBW NextMove e100 8 axis motion controller. Differential stepper outputs
NXE100-1608SBW
NextMove e100 8 axis motion controller. Single ended open collector stepper outputs for use with DSM integrated stepper/driver motors
NXE100-1612DBW NextMove e100 12 axis motion controller. Differential stepper outputs
NXE100-1612SBW
NextMove e100 12 axis motion controller. Single ended open collector stepper outputs for use with DSM integrated stepper/driver motors
NXE100-1616DBW NextMove e100 16 axis motion controller. Differential stepper outputs
NXE100-1616SBW
NextMove e100 16 axis motion controller. Single ended open collector stepper outputs for use with DSM integrated stepper/driver motors
OPT036-501 Ethernet POWERLINK Router for remote connection / access to to a POWERLINK system / network
CBL001-501
2m (6ft) RS232 cable for programming and diagnostics
(note: 2m (6ft) USB cable included with the motion controller)
CBL034-501
RS232 programming cable (PC to HMI)
MNC001-501 MintNC - Windows profiling front end for NextMove which accepts industry standard files: HPGL, DXF and G-code.
HMI - see ABB operator panels
24V power supplies - see ABB power supplies
Ethernet cables - For connecting NextMove e100 to MicroFlex e100
CBL002CM-EXS Ethernet Cable: Shielded CAT5e RJ45 200mm / 8in
CBL005CM-EXS Ethernet Cable: Shielded CAT5e RJ45 500mm / 1.6ft
CBL010CM-EXS Ethernet Cable: Shielded CAT5e RJ45 1m / 3.2ft
CBL020CM-EXS Ethernet Cable: Shielded CAT5e RJ45 2m / 6.5ft
CBL050CM-EXS Ethernet Cable: Shielded CAT5e RJ45 5m / 16.3ft
CBL100CM-EXS Ethernet Cable: Shielded CAT5e RJ45 10m / 32.6ft